Driveshaft split pins

Renault & Alpine General Discussion
User avatar
User

Juzzblack

Rank

Non Member

Posts

982

Joined

Sun May 16, 2004 10:49 pm

Location

Charlotte, USA


Has thanked: 0 time
Been thanked: 0 time

Postby Juzzblack » Tue Apr 01, 2008 11:43 am

I need to fit a new drivers side drive shaft. Any tips? How easy/hard a job is it?

And besides a new roll pin are there any other bits I have to replace with new when fitting the new drive shaft?

Cheers.
GTA V6 Turbo - BTW check your earths!

Image

http://www.youtube.com/user/AlpineGTA
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Tue Apr 01, 2008 11:54 am

Easy to do .Slacken the hub nut ,knock the split pins out ,remove the upper hub mount bolt and pivot the shaft out from the box ,then take the hub nut off and pull the shaft out .
There are two split pins ,one 6 mm and one that goes up it's chuff ,about 3 mm .
You might want to look a the gearbox seals at the same time .
Remember to fill the split pins with sealant when they're back in .
User avatar
User

simontaylor

Rank

Non Member

Posts

5602

Joined

Thu Apr 15, 2004 12:33 pm

Location

Fleet, Hampshire


Has thanked: 44 times
Been thanked: 56 times

Postby simontaylor » Tue Apr 01, 2008 2:43 pm

and the pins will probably only go back into the shaft if it is on the box the same way it came off, else you will have to rotate the shaft 180 degrees. Might be worth marking up as it comes off??? especially as access is a lot more restrictive when the box is still in the car.

I just used a nail with the piont cut off to drift the pins out.
1986 : '86 GTA v6 BW-EFR turbo, with Adaptronic ECU
Firsts at
2007 : Gurston Down & RAOC Champion
2008 : Rushmoor & Eelmoor & ACSMC Hillclimb class Champion
2009 : Longcross & Eelmoor
2010 : Crystal Palace & Eelmoor
2016 : Rushmoor & 5th O/A
User avatar
User

Stunned Monkey

Rank

Non Member

Posts

1514

Joined

Tue Apr 12, 2005 12:24 am

Location

Nr Chippenham, Wiltshire


Has thanked: 0 time
Been thanked: 3 times

Postby Stunned Monkey » Tue Apr 01, 2008 3:12 pm

I have a superb "tool" for knocking the pins out - it's one of the front rocker cover cap screws from a 3 litre PRV - an extremely long high tensile M6 cap screw. Perfect.
Martin - PRV Tinkerererer
www.delorean.co.uk
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Tue Apr 01, 2008 3:20 pm

I use a new roll pin to push out the old :|
User avatar
User

Stunned Monkey

Rank

Non Member

Posts

1514

Joined

Tue Apr 12, 2005 12:24 am

Location

Nr Chippenham, Wiltshire


Has thanked: 0 time
Been thanked: 3 times

Postby Stunned Monkey » Tue Apr 01, 2008 3:23 pm

And that works... how? :wink:
Martin - PRV Tinkerererer
www.delorean.co.uk
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Tue Apr 01, 2008 3:41 pm

I use a new roll pin to push out the old :|
User avatar
User

Stunned Monkey

Rank

Non Member

Posts

1514

Joined

Tue Apr 12, 2005 12:24 am

Location

Nr Chippenham, Wiltshire


Has thanked: 0 time
Been thanked: 3 times

Postby Stunned Monkey » Tue Apr 01, 2008 4:28 pm

Leaving you with a roll pin that needs pushing out....
Martin - PRV Tinkerererer
www.delorean.co.uk
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Tue Apr 01, 2008 4:37 pm

I use an old roll pin to push out the new :|
User avatar
User

si21

Rank

Non Member

Posts

2094

Joined

Mon May 09, 2005 8:24 pm

Location

S.E London


Has thanked: 3 times
Been thanked: 2 times

You Said it LOL

Postby si21 » Tue Apr 01, 2008 4:41 pm

clee wrote:
Before you say yes I know its a bolt size spose if it gets somebody outta trouble, but you just cant beat having the proper tool to do the Job


All the gear ,No f###ing idea :wink:


:lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol:
si21 :wink:
User avatar
User

si21

Rank

Non Member

Posts

2094

Joined

Mon May 09, 2005 8:24 pm

Location

S.E London


Has thanked: 3 times
Been thanked: 2 times

Re: You Said it LOL

Postby si21 » Tue Apr 01, 2008 4:43 pm

si21 wrote:
clee wrote:
Before you say yes I know its a bolt size spose if it gets somebody outta trouble, but you just cant beat having the proper tool to do the Job


All the gear ,No f###ing idea :wink:


:lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol: :lol:
si21 :wink:


STEVE F**K OFF AND PUT THAT F~CKING HEAP OF SH*TE ON AS YOUR OWN AVITAR SINCE YOU LIKE IT SO MUCH! :evil:

MODERATE THAT :lol: :lol: :lol: :lol:
User avatar
User

Stunned Monkey

Rank

Non Member

Posts

1514

Joined

Tue Apr 12, 2005 12:24 am

Location

Nr Chippenham, Wiltshire


Has thanked: 0 time
Been thanked: 3 times

Postby Stunned Monkey » Tue Apr 01, 2008 8:06 pm

I think it suits you :lol:
Martin - PRV Tinkerererer
www.delorean.co.uk
User avatar
User

si21

Rank

Non Member

Posts

2094

Joined

Mon May 09, 2005 8:24 pm

Location

S.E London


Has thanked: 3 times
Been thanked: 2 times

You Would

Postby si21 » Wed Apr 02, 2008 1:23 pm

Stunned Monkey wrote:I think it suits you :lol:


BATTY BOY jesus how many of you guys have got Little pink tanks in your clossets :lol: :lol: :lol: :lol:
User avatar
User

Stunned Monkey

Rank

Non Member

Posts

1514

Joined

Tue Apr 12, 2005 12:24 am

Location

Nr Chippenham, Wiltshire


Has thanked: 0 time
Been thanked: 3 times

Postby Stunned Monkey » Wed Apr 02, 2008 3:51 pm

I'm not the one using one as my avatar... I said it suits YOU, sir :P
Martin - PRV Tinkerererer
www.delorean.co.uk
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Wed Apr 02, 2008 4:16 pm

That's why no one wants to share a tent with him :shock: :wink:
PreviousNext


  • Advertisement

Who is online

Users browsing this forum: No registered users and 255 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France