Hoses going to the heater matrix

Renault & Alpine General Discussion
User avatar
User

mettersl

Rank

Club Member

Club Member
Posts

2027

Joined

Sat Nov 13, 2004 12:46 pm

Location

Saffron Walden- North Essex


Has thanked: 23 times
Been thanked: 59 times

Postby mettersl » Thu Sep 01, 2011 12:37 pm

How about shortening the pipes on the matrix so they don't go through the bulkhead and can then can come out inside the car?
Could you make it watertight afterwards?

Just a thought
Lee
no avatar
User

Alpineandy

Rank

Club Member

Club Member
Posts

2381

Joined

Mon Jun 14, 2004 8:37 am

Location

North Essex


Has thanked: 5 times
Been thanked: 10 times

Postby Alpineandy » Thu Sep 01, 2011 12:43 pm

clee wrote:Fecker won't spill the beans :lol: Well , says he will but only after they have all been to Belfast and had the job done :roll: :wink:

Clee, you forgot to add 'and after you've bought him beers all night long'!

Or is it just me that would expect this before telling anyone anything useful (....if I ever knew anything useful!). :lol:
Alpine A110, Renault Safrane 2.5dt, Hudson Kindred Spirit (Renault powered), transAlp (Honda) and Ducati Multistrada
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Thu Sep 01, 2011 1:11 pm

mettersl wrote:How about shortening the pipes on the matrix so they don't go through the bulkhead and can then can come out inside the car?
Could you make it watertight afterwards?

Just a thought
Lee


I thought he might be after taking the end tank off ....he say no but you never know with the Irish ....might be just winding up the eeejut English again

I don't think there is a Pub with enough beers to lossen his tongue Andy .

Anyway I'm now on to taking the manifold off to replace all the water pipes there also ...watch him pop up and laugh ..
".te-be-sure I can do dat without even lifting the engine cover ...so I can ..."
User avatar
User

jonc

Rank

Non Member

Posts

382

Joined

Mon Jul 16, 2007 11:08 am

Location

Oxfordshire


Has thanked: 24 times
Been thanked: 6 times

Postby jonc » Thu Sep 01, 2011 2:51 pm

Fair enough - I can understand not wanting to publish 'trade' secrets but personally, I like to know what's going to happen to my car in the process and how things will end up when it's all done, especially if it's not the 'by the book' approach. That's not to say that I think that there's a dodgy solution going on here but I'd need some reassurance about what's involved before making a trip to Belfast! ;)

I'd considered trimming the matrix pipes off on the inside of the bulkhead to get the old matrix out, doing the same on the new matrix and then use short hoses to fit the new matrix to the old through-the-bulkhead pipes but IIRC there's not much pipe available for that!

In fact, I was impressed, Lee, that you'd got all that out without removing the centre console (something that I believe the manual says you have to do - but we all know manuals don't always describe the best approach). That looked like a definite pre-requisite when I was last looking at all this.

Thankfully, so far I have not needed to go to this stage.
Previous


  • Advertisement

Who is online

Users browsing this forum: No registered users and 222 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France