Oil leak.

Renault & Alpine General Discussion

Moderators: eastlmark, BIG_MVS, phildini, Test Moderator, Alpineandy

User avatar
User

Juzzblack

Rank

Non Member

Posts

982

Joined

Sun May 16, 2004 10:49 pm

Location

Charlotte, USA


Has thanked: 0 time
Been thanked: 0 time

Oil leak.

Postby Juzzblack » Mon Mar 14, 2005 7:02 pm

Is it just me, or am I the only one who seems to have constant engine woes? Everyone else seems to enjoy tinkering and tuning, whereas I am always fixing! :( Anway, my problem... :roll:

Since getting my car back after all the engine work, I've noticed an oil leak. It's dripping off the bottom of the timing cover but I don't think this is where it's leaking from. It's such an oily mess it's difficult to say where it's leaking from, but it's down the right hand side back of the engine. The right hand side of the timing cover and the bottom of the distributor are covered in oil.

I didn't think the timing chains ran in oil do they? I wouldn't expect to leak much oil from the timing cover gasket if it was that and the cam cover gaskets look dry. I wondered if there might be an oil seal on the distributor and if it could be this? Might account for the mess it's making if it's spraying oil arround as it rotating?

Is the distributor difficult to take off to change the oil seal and put back again? Assuming it does have an oil seal. The Renault parts book seems to show a round seal.

Cheers.
GTA V6 Turbo - BTW check your earths!

Image

http://www.youtube.com/user/AlpineGTA
User avatar
User

darrenbiggs

Rank

Non Member

Posts

1499

Joined

Thu Apr 29, 2004 1:03 pm

Location

Horley - Nr Gatwick


Has thanked: 15 times
Been thanked: 39 times

Distributor oil seal

Postby darrenbiggs » Mon Mar 14, 2005 8:09 pm

I think there is a seal around the distributor - I remember having mine replaced long ago, not very difficult to fix as GTA things go. I'd try to check thats where its coming from first though.

Also be careful it doesn't start to effect the ignition!
User avatar
User

Juzzblack

Rank

Non Member

Posts

982

Joined

Sun May 16, 2004 10:49 pm

Location

Charlotte, USA


Has thanked: 0 time
Been thanked: 0 time

Postby Juzzblack » Mon Mar 14, 2005 9:14 pm

I'll clean it all up and try and establish for certain where it's coming from. But if it is that it'll be much easier than changing the timing cover gasket!

Cheers.
GTA V6 Turbo - BTW check your earths!

Image

http://www.youtube.com/user/AlpineGTA
User avatar
User

stephendell

Rank

Club Member

Club Member
Posts

7463

Joined

Wed Apr 14, 2004 7:25 pm

Location

London


Has thanked: 125 times
Been thanked: 102 times

Postby stephendell » Mon Mar 14, 2005 11:55 pm

Timing cover gasket is not too bad to change once you have removed the exhaust & crankshaft pulley. There is also an oil seal for the crankshaft pulley that may need changing. There is plenty of scope for leaks around here especially if the timing cover bolts have been fitted incorrectly. There are two or three different lengths around the cover and it's easy to strip threads or fit bolts that are too short.
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Tue Mar 15, 2005 5:53 pm

It could be as simple as the end of the rocker cover. I had a small trickle on a car once, which ran down the edge of the timing cover and the bottom of the dizzy, so I assumed it was the cam seal..if it is the cam seal though, the dizzy will fill up with oil, so check that first.

So all it needed was a new rocker gasket and check the tightness of the two end bolts at the front of the engine.
Image
User avatar
User

Juzzblack

Rank

Non Member

Posts

982

Joined

Sun May 16, 2004 10:49 pm

Location

Charlotte, USA


Has thanked: 0 time
Been thanked: 0 time

Postby Juzzblack » Tue Mar 15, 2005 6:55 pm

The cam cover gasket on that side is new and wasn't disturbed when the timing was re-done and as it looks clean and leak free and it seems to be originating from higher up than the crank pulley, and after chatting to Andrew from CAR, he reckoned the distributor oil seal was the most likely cause.

Since this sounds like a relatively easy and cheap job to change, I think I'll try changing this first. I called in at Renault today and ordered the seal; about £13.

So that's my job for the weekend... :roll:
GTA V6 Turbo - BTW check your earths!

Image

http://www.youtube.com/user/AlpineGTA
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Tue Mar 15, 2005 7:43 pm

Juzzblack wrote:The cam cover gasket on that side is new and wasn't disturbed when the timing was re-done and as it looks clean and leak free and it seems to be originating from higher up than the crank pulley, and after chatting to Andrew from CAR, he reckoned the distributor oil seal was the most likely cause.

:


The cam cover overlaps the timing chain cover though, so it will still be disturbed. The easiest way to check if it is the cam shaft seal, is just to slacken off the cap slightly and see if oil pours out..
Image


  • Advertisement

Who is online

Users browsing this forum: No registered users and 216 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France